- What size wire do I need for a 200 amp service?
- What size wire should I use for a pool pump?
- How much current can a 2.5 mm cable carry?
- What size wire do I need for 30 amps?
- What size breaker do I need for a 2 hp motor?
- What size cable do I need for 32 amps?
- How many amps does a 1 hp pump draw?
- How many amps does a 1.5 HP pool pump draw?
- Does pool pump use a lot of electricity?
- How far can you run 12 gauge wire on a 20 amp circuit?
- What size breaker do I need for a 1/2 HP well pump?
- How many watts can a 2.5 mm cable take?
- Can 6mm take 40a?
- What is 2.5 mm cable used for?
- What current can 4mm cable carry?
- How much load can a 4mm cable take?
- What size wire do I need for a 10 hp motor?
- How many amps does a 2 HP pool pump draw?
- How do you calculate the cable size of an HP motor?
- How do I calculate what size wire I need?
- What size wire do I need for a 200 amp underground service?

## What size wire do I need for a 200 amp service?

SERVICE ENTRANCE CONDUCTORS SIZE AND RATINGService or Feeder RatingCopper ConductorsAluminum or Copper-Clad Aluminum125 Amps#2 AWG#1/0 AWG150 Amps#1 AWG#2/0 AWG200 Amps#2/0 AWG#4/0 AWG1 more row.

## What size wire should I use for a pool pump?

Lastly your pool pump motor must be bonded in accordance with local electrical code requirements. Use a solid copper conductor, size 8 AWG or larger. Run this wire from from a reinforcing rod to the pressure wire connector provided on the motor housing.

## How much current can a 2.5 mm cable carry?

A 2.5mm cable is capable of supplying around 23-25 amps depending on the method of installation, so is fine, safe and compliant on a 20amp circuit breaker.

## What size wire do I need for 30 amps?

Any circuit fused for 30 amps must use a minimum of 10 ga copper or 8 ga alu. Longer runs may require an upgrade of wire size.

## What size breaker do I need for a 2 hp motor?

Full Load Current: Three Phase AC MotorsMotor HorsepowerSize Breaker2230V 460V15 153230V 460V15 155230V 460V15 157-1/2230V 460V40 306 more rows•Feb 16, 2017

## What size cable do I need for 32 amps?

For 32 amps you would require 6mm twin and earth cable.

## How many amps does a 1 hp pump draw?

10 ampsHow many watts does a 240v well pump use? A 1HP 240 volt pump pulls 10 amps while running.

## How many amps does a 1.5 HP pool pump draw?

How many amps does a pool pump use?HorsepowerAmpsVoltage.75 HP5.18 A120 V1 HP6.91 A120 V1.25 HP8.63 A120 V1.5 HP10.4 A120 VJun 3, 2020

## Does pool pump use a lot of electricity?

Outside of the air conditioner, the pool pump is the largest electricity consumer in the average pool-containing home. According to the study, at the national average of 11.8 cents per KWh, a pool pump alone can add as much as $300 a year to an electric bill.

## How far can you run 12 gauge wire on a 20 amp circuit?

The total circuit would be about 60 -70 feet in length. It would only be supplying about 5 outlets and one light. It would be a light load, running small things, no heaters or med/large equipment. #12 provides reasonable performance up to about 100′ with general loads like you describe.

## What size breaker do I need for a 1/2 HP well pump?

For a 1/2 HP submersible pump, a 15 amp 2 pole breaker would be normal. You can run 12 AWG, but unless the run is very long, 14 AWG is sufficient. Bigger wire would let you switch to a bigger pump later if you wanted.

## How many watts can a 2.5 mm cable take?

Choosing the correct size cableConductor SizeCurrentMaximum power (Watts)1.25 mm213 ampsUp to 3120 Watts1.5 mm215 ampsUp to 3600 Watts2.5 mm220 ampsUp to 4800 Watts4.0 mm225 ampsUp to 6000 Watts1 more row

## Can 6mm take 40a?

2 Answers from MyBuilder Electricians 6mm twin and earth cable (which this almost certainly is) can be backed up by a maximum of a 32a MCB, even lower if other factors are involved. You’ll need that 10mm cable and a 40a MCB unfortunately as your shower is going to draw over 32a.

## What is 2.5 mm cable used for?

2.5mm Twin and Earth is commonly used as indoor domestic cable. The most common use for this type of cable is for circuits that provide power to sockets. It is made up of two cores and an earth core which must be covered with the identifying green and yellow sleeve when installed.

## What current can 4mm cable carry?

Cable Size Ratings in AmpsCable sizeRating in Amps1mm15.51.5mm202.5mm274mm372 more rows

## How much load can a 4mm cable take?

So, current carrying capacity of 4mm sq copper wire is = 20–25 amp depending on how you are placing it and in what atmosphere.

## What size wire do I need for a 10 hp motor?

Electrical motor wiring data – NEMA amps, starter size, HMCP size for motors ranging 1/2 to 500 hpMotor HPNEMA ampsPhase Wires (AWG)57.5127 1/2111210141215211021 more rows

## How many amps does a 2 HP pool pump draw?

The Amps are listed as 15.0 / 7.5 – which means that at 115V the motor draws 15A, and at 230V the draw is 7.5 Amps. For a larger motor over 2hp, you will commonly see only 230V listed and a single number to represent Amps used at maximum load. Note that the pump label or ‘name plate’ shows the Maximum Amp Draw.

## How do you calculate the cable size of an HP motor?

Size of Cable for Branch circuit which has Single Motor connection is 125% of Motor Full Load Current Capacity. Example: what is the minimum rating in amperes for Cables supplying 1 No of 5 hp, 415-volt, 3-phase motor at 0.8 Power Factor. Full-load currents for 5 hp = 7Amp. Min Capacity of Cable= (7X125%) =8.75 Amp.

## How do I calculate what size wire I need?

VDI = AMPS x FEET ÷ (% VOLT DROP x VOLTAGE)Amps = Watts divided by volts.Feet = One-way wire distance.% Volt Drop = Percentage of voltage drop acceptable for this circuit (typically 2% to 5%)

## What size wire do I need for a 200 amp underground service?

Similarly, what size wire do I need for a 200 amp underground service? You need a minimum of #6 ground or #4 aluminum for 200 amps. I would recommend just getting 4/0-4/0-2/0-4 quadplex as it is all rated for direct burial. A conductor is a wire that is used to carry electrical power.